Deer Day 13 - Sunday Nov 3

First off, apologies to any of my avid reader fans out there (yes, both of you).  Spent the week post elk camp getting over a cold and working on my journal from the elk trip.  Have been absent from this blog and am just now getting back to it.

Kathy and Alex were the only 2 to go out on Sunday afternoon.  They sat in the stands on Neal.
They saw a pretty sunset and one deer as they drove home.  Nothing else moving.  Still too warm.

Dave Jones drove by and saw the truck - and the large doe standing about 30 feet from the truck.  As Dad always says - I would've killed more deer if I'd stayed in the truck.  True...


The view from Kathy's stand - with the crossbow.


The view from Alex's stand.  Note the absence of deer.


One gorgeous sunset as they leave the woods!


Comments

Post a Comment

Popular posts from this blog

Winchester SX4 Trigger Assembly Update

Image
First, you need to read the post immediately before this one to understand why I had to take my Winchester SX4 shotgun apart - all the way apart - specifically the trigger assembly. Second, my bad.  I had neglected to clean the gun after returning from last October's pheasant trip.  I had about one bale of grass seed inside that gun, which in the end, may have kept the #8 pellet from getting out on its own.  Shame. Finally, I did not give up.  I watched four different YouTube videos on how to disassemble and reassemble the trigger group.  Sadly, no one did the SX4, only the previous version, the SX3.  Close enough.  Why did it take 4 videos?  Because no one explained HOW the damn sear goes back in.  Everyone either ASSUMED we all know how OR in two cases, the reassembly process was out of the camera frame.  Aggravating! The key, and this is more for me to remember, was on the fourth video, the author said, "The sear kinda slides down int...
Read more

Cleaning Winchester SX3 / SX4 Shotguns

Image
The Winchester SX4 is my Go To shotgun for everything - clays, doves, ducks, geese, pheasants, whatever.  It is an awesome firearm.  The drawback?  There are multiple moving parts and a few of them like to collect carbon.  And this carbon sticks as if it were put on those parts with super glue! Specifically, the magazine tube and the gas piston are the main carbon collectors.  Those parts come out more black than silver & gold. The inner components of an SX3 / SX4 with highlights where carbon will form So what is my trick for cleaning those bits?  I drop the gas piston into my Hornady sonic cleaner.  Inside the cleaner I put in about a cup of Hornady's One Shot Sonic Clean Solution for gun parts, add some DI water, a couple squirts of Dawn liquid dish soap, and then top it off with a dash or two of the citrus version of Dr. Bronner's pure castile liquid soap.  I have found that the citrus Dr. Bronner's is awesome at removing grease and oil....
Read more

Ferris IS2000Z Maintenance

Image
You know, there is a lot of good information out there on the 'internets.'  But not everything is there, and not all of it is useful.  I am guilty of some of both of those as well... My Ferris IS 2000Z had an intermittent problem with the blades not wanting to engage.  You could pull the PTO switch and nothing.  Jiggle it a bit or move it and sometimes the blades would come on.  Well, this past Sunday afternoon, it decided not only that it would not come on, but that it would send a signal that the blades WERE on so the mower would not start. I hit the Google to find out what part I should buy.  Amazon was very helpful; not only did they show pictures, but offered technical guidance on what switch to buy.  That bit was easy.  I picked two-day shipping and the part arrived in the mail Tuesday.  $17 and some change.  No worries. So, to change a PTO or blade switch on a Ferris mower, or specifically a Ferris IS 2000Z, you lift up the ...
Read more