Garage Expansion - Update

So we have decided that parking our vehicles out in the elements has come to an end.  But, in order to get our SUVs into the garage, it must be expanded.  So that's what we're doing.  Actually, that's what we have hired a contractor to do for us.

The S wall was brick, so we saved those to put back on the W wall.  This way they will match.

We blew out the S wall and are adding 6 feet 8 inches as that will allow the proper spacing for the rafters as well as give us enough room for wider garage doors.

The E wall, where the doors are, will get a new header & wider doors installed.

We grabbed a permit, had the foundation dug, and the floor is now poured.  Making progress!

 
S wall gone (tarped with black pastic) and footers dug

 
Concrete has arrived

 
Concrete footers being poured

 
Slab floor being poured

 
A view from inside the garage facing out (to the S).
Floor is poured and finished.

Comments

Post a Comment

Popular posts from this blog

Cleaning Winchester SX3 / SX4 Shotguns

Image
The Winchester SX4 is my Go To shotgun for everything - clays, doves, ducks, geese, pheasants, whatever.  It is an awesome firearm.  The drawback?  There are multiple moving parts and a few of them like to collect carbon.  And this carbon sticks as if it were put on those parts with super glue! Specifically, the magazine tube and the gas piston are the main carbon collectors.  Those parts come out more black than silver & gold. The inner components of an SX3 / SX4 with highlights where carbon will form So what is my trick for cleaning those bits?  I drop the gas piston into my Hornady sonic cleaner.  Inside the cleaner I put in about a cup of Hornady's One Shot Sonic Clean Solution for gun parts, add some DI water, a couple squirts of Dawn liquid dish soap, and then top it off with a dash or two of the citrus version of Dr. Bronner's pure castile liquid soap.  I have found that the citrus Dr. Bronner's is awesome at removing grease and oil....
Read more

Winchester SX4 Trigger Assembly Update

Image
First, you need to read the post immediately before this one to understand why I had to take my Winchester SX4 shotgun apart - all the way apart - specifically the trigger assembly. Second, my bad.  I had neglected to clean the gun after returning from last October's pheasant trip.  I had about one bale of grass seed inside that gun, which in the end, may have kept the #8 pellet from getting out on its own.  Shame. Finally, I did not give up.  I watched four different YouTube videos on how to disassemble and reassemble the trigger group.  Sadly, no one did the SX4, only the previous version, the SX3.  Close enough.  Why did it take 4 videos?  Because no one explained HOW the damn sear goes back in.  Everyone either ASSUMED we all know how OR in two cases, the reassembly process was out of the camera frame.  Aggravating! The key, and this is more for me to remember, was on the fourth video, the author said, "The sear kinda slides down int...
Read more

Determine Sex of Deer from Tracks

Image
It IS possible to determine from a set of tracks whether the deer you are tracking is a doe (female) or a buck (male).  And, it's actually pretty simple if you know a few facts about deer. First, you have to know what a deer track looks like.  Deer leave a track that looks like the outline of a heart. Next, you have to know the direction of travel.  Deer are moving toward the "pointy" end of the heart.  So in the above example, the deer is traveling toward the top of this post, or up. Here is an actual photo of deer tracks in the wild so you can get a better idea.  Again, this deer is traveling up, or towards the top of this page.  (It is also clear that this deer was STANDING, not walking - well clear enough to me.  Read on to find out why I know that). Sometimes if the ground is soft or if the deer is traveling really fast (jumping), the track left will show the deer's dew claws at the rear of the direction traveling, like so: The ...
Read more