Update on the 1k Range

Been working quite some time to get dirt in for a backstop.  It finally arrived, but the crops were in.  Crops are out now, so we went back to the dirt pile and installed our target frame.  It's a 4'x4' (1.2 metres square) piece of plywood surrounded by 4"x4" posts buried 36" deep on deck stabilizers - to make it easier to replace when it rots or gets shot thru.

The kids love climbing on it as well as the dogs and deer.  The following pictures are just interim - or as we build.  I still have 5 gongs to hang - A500 steel silhouette and gongs from 6" - 18" (15 cm - 45 cm).  All to be shot from 1,000 down to 100 yards (915 - 91.5 metres).  

Then to finish, I need to delineate the yardages and plant alfalfa to shoot over.

 
Mallory, Papaw and Tiki on top the hill (Tiki is in our shadow).
This is the backside of the backstop.

 
A selfie of Papaw & Mallory on top with Grandma & Wes below.
The picture looks to the S, or where we will be firing from.

 
Grandma & Mallory walking back from the dirt pile

 
Grandma & the kids having fun on the swings after our walk

 
Davey Jones & MPK helped to set the 4x4' target stand 36" deep

 
Will & Tiki on top, inspecting our work

 
Frame up and temporarily held in place & plumb.
These front supports will be removed.  Supports from the rear will be installed.


Comments

Post a Comment

Popular posts from this blog

Cleaning Winchester SX3 / SX4 Shotguns

Image
The Winchester SX4 is my Go To shotgun for everything - clays, doves, ducks, geese, pheasants, whatever.  It is an awesome firearm.  The drawback?  There are multiple moving parts and a few of them like to collect carbon.  And this carbon sticks as if it were put on those parts with super glue! Specifically, the magazine tube and the gas piston are the main carbon collectors.  Those parts come out more black than silver & gold. The inner components of an SX3 / SX4 with highlights where carbon will form So what is my trick for cleaning those bits?  I drop the gas piston into my Hornady sonic cleaner.  Inside the cleaner I put in about a cup of Hornady's One Shot Sonic Clean Solution for gun parts, add some DI water, a couple squirts of Dawn liquid dish soap, and then top it off with a dash or two of the citrus version of Dr. Bronner's pure castile liquid soap.  I have found that the citrus Dr. Bronner's is awesome at removing grease and oil.  All of that bakes in the son
Read more

Winchester SX4 Trigger Assembly Update

Image
First, you need to read the post immediately before this one to understand why I had to take my Winchester SX4 shotgun apart - all the way apart - specifically the trigger assembly. Second, my bad.  I had neglected to clean the gun after returning from last October's pheasant trip.  I had about one bale of grass seed inside that gun, which in the end, may have kept the #8 pellet from getting out on its own.  Shame. Finally, I did not give up.  I watched four different YouTube videos on how to disassemble and reassemble the trigger group.  Sadly, no one did the SX4, only the previous version, the SX3.  Close enough.  Why did it take 4 videos?  Because no one explained HOW the damn sear goes back in.  Everyone either ASSUMED we all know how OR in two cases, the reassembly process was out of the camera frame.  Aggravating! The key, and this is more for me to remember, was on the fourth video, the author said, "The sear kinda slides down into a channel in the housing."  Bam. 
Read more

Determine Sex of Deer from Tracks

Image
It IS possible to determine from a set of tracks whether the deer you are tracking is a doe (female) or a buck (male).  And, it's actually pretty simple if you know a few facts about deer. First, you have to know what a deer track looks like.  Deer leave a track that looks like the outline of a heart. Next, you have to know the direction of travel.  Deer are moving toward the "pointy" end of the heart.  So in the above example, the deer is traveling toward the top of this post, or up. Here is an actual photo of deer tracks in the wild so you can get a better idea.  Again, this deer is traveling up, or towards the top of this page.  (It is also clear that this deer was STANDING, not walking - well clear enough to me.  Read on to find out why I know that). Sometimes if the ground is soft or if the deer is traveling really fast (jumping), the track left will show the deer's dew claws at the rear of the direction traveling, like so: The two little "
Read more