Spring Kit Installation for T/C Encore

So Krueger is doing some snooping around on the internet trying to figure out what barrel to put on his Thompson / Center (T / C) Encore muzzle loader.  The problem is that the trigger is not the best for precision shooting.  That leads to an investigation on what to do to improve the trigger function on the T / C Encore so that he could get excellent groups.

Turns out that Mike Bellm's T/Cs provides multiple spring kits (at different poundages) for $20.  This turns out to be a Great Deal for 5 springs that will definitely improve your trigger function!  You can go to Mike's website to buy direct here:  https://www.bellmtcs.com/
Go to Store Categories -> Shop and pick the right spring kit for your gun and your preferred poundage.



We order the Encore 2.5# spring kits and await their arrival.  Kruger comes over and we tear our guns apart - carefully.

Thanks to the wonderful research tool that is YouTube, we utilized the following video to help us take them apart and install the new kit.

https://www.youtube.com/watch?reload=9&v=Jo_LAH9of14&feature=youtu.be

I wish I could give this guy credit, but I could not find his name anywhere.  So whoever you are, thank you very much.  This video covers 98% of everything you need to tear down your T/C Encore, remove the old springs, install the new ones, and reassembly your gun.

Our only issue arrived when we tried to put the trigger spring back in.  The orientation is well presented, but the actual location of the back pin is VERY difficult to see in the video.  We guessed the first time and were wrong.  Locked up the whole gun.  We pulled it back apart and saw that we were making it too difficult on ourselves - the spring just drops into place.  No reason to "put" the back pin anywhere.

Trust me on this bit - grab a good buddy and have some help, especially with the trigger spring.  The guy in the video does it by himself, but it is way easier with four hands.  Watching the video, pausing it as we went, and moving step-by-step, we completed this installation the first time in 1 hour.

After we got my gun complete, we tackled Krueger's gun.  Since we had the knowledge and did not have to watch the video as we went, we installed his spring kit in 15 minutes.  Of course we only had to install his trigger spring once.  That saved some time.

Overall, this is the best $20 I have spent in a long time.  We are guessing as we do not have trigger gauges, but my T/C was between 5 - 6# before this installation.  Afterwards, it is 1.5 - 2#.  This. Kit. Works!

Krueger's gun was a bit different, starting somewhere higher and ending just north of #2.  A lot of what you get depends upon your gun and how it was made and when.  You start with good and you get better after installing this kit.

If you are looking to improve your T/C's trigger, then this kit is a must!  Done.

Comments

Post a Comment

Popular posts from this blog

Cleaning Winchester SX3 / SX4 Shotguns

Image
The Winchester SX4 is my Go To shotgun for everything - clays, doves, ducks, geese, pheasants, whatever.  It is an awesome firearm.  The drawback?  There are multiple moving parts and a few of them like to collect carbon.  And this carbon sticks as if it were put on those parts with super glue! Specifically, the magazine tube and the gas piston are the main carbon collectors.  Those parts come out more black than silver & gold. The inner components of an SX3 / SX4 with highlights where carbon will form So what is my trick for cleaning those bits?  I drop the gas piston into my Hornady sonic cleaner.  Inside the cleaner I put in about a cup of Hornady's One Shot Sonic Clean Solution for gun parts, add some DI water, a couple squirts of Dawn liquid dish soap, and then top it off with a dash or two of the citrus version of Dr. Bronner's pure castile liquid soap.  I have found that the citrus Dr. Bronner's is awesome at removing grease and oil....
Read more

Winchester SX4 Trigger Assembly Update

Image
First, you need to read the post immediately before this one to understand why I had to take my Winchester SX4 shotgun apart - all the way apart - specifically the trigger assembly. Second, my bad.  I had neglected to clean the gun after returning from last October's pheasant trip.  I had about one bale of grass seed inside that gun, which in the end, may have kept the #8 pellet from getting out on its own.  Shame. Finally, I did not give up.  I watched four different YouTube videos on how to disassemble and reassemble the trigger group.  Sadly, no one did the SX4, only the previous version, the SX3.  Close enough.  Why did it take 4 videos?  Because no one explained HOW the damn sear goes back in.  Everyone either ASSUMED we all know how OR in two cases, the reassembly process was out of the camera frame.  Aggravating! The key, and this is more for me to remember, was on the fourth video, the author said, "The sear kinda slides down int...
Read more

Determine Sex of Deer from Tracks

Image
It IS possible to determine from a set of tracks whether the deer you are tracking is a doe (female) or a buck (male).  And, it's actually pretty simple if you know a few facts about deer. First, you have to know what a deer track looks like.  Deer leave a track that looks like the outline of a heart. Next, you have to know the direction of travel.  Deer are moving toward the "pointy" end of the heart.  So in the above example, the deer is traveling toward the top of this post, or up. Here is an actual photo of deer tracks in the wild so you can get a better idea.  Again, this deer is traveling up, or towards the top of this page.  (It is also clear that this deer was STANDING, not walking - well clear enough to me.  Read on to find out why I know that). Sometimes if the ground is soft or if the deer is traveling really fast (jumping), the track left will show the deer's dew claws at the rear of the direction traveling, like so: The ...
Read more